AGA T2

  
Yes, we realize this ubiquitous Genesis-style atomizer has been reviewed to death, but it’s almost a requirement, if you’re going to own gennies, that this one has to be in the collection. As far as bargain-basement Genesis atomizers go, it’s the de-facto standard.
The AGA-T version 2 is a stainless steel Genesis-type atomizer, meaning that it is intended to be used with a rolled, stainless steel mesh wick, at the top of which a wire coil is placed to vaporize the juice as it is drawn up from a tank below. This is considered by many to actually be the third major revision of the AGA-T line, though other than the glass tank, it is identical to the second, usually referred to as the AGA-T+.
Other than the borosilicate tank, other differences from the original AGA-T include a press-on cap that allows throat hit adjustment by positioning the air hole, and a somewhat cleaner look as the result of the elimination of knurling on the exterior parts. Both have been mostly regarded as major improvements to this atomizer.
Like other Genesis atomizers, how well the AGA-T2 performs is going to depend mostly on the wick and coil you set it up with. The atomizer does not come with a wick and coil pre-installed, though small pieces of stainless steel mesh and resistance wire are included in a tiny packet in the box. We chose not to use those, mostly because it was not apparent what materials were used, or the specification of the mesh and wire. We opted instead for known quantities, using our own mesh and kanthal wire for testing.
We tested the AGA-T2 with two builds: one using 400 mesh and 32-gauge kanthal, for a coil resistance of approximately 2.0Ω, and a second build using 28-gauge kanthal and 400 mesh, with a resistance of .9Ω. The AGA-T2 performed very well under both configurations. We ran into no issues with wicking or leaks, vapor production was copious, and taste was excellent. Granted, more credit for this performance probably belongs to our own skills at setting up a Genesis than to the AGA-T2 itself, but nothing about the AGA-T2 made it particularly difficult.
It should probably be noted that many have noted a problem with hot spots at the top of the coil on the AGA-T2. While most blame the distance from the coil to the top post, we find it far more likely to be the result of the way the top of the coil is connected between two very small nuts on the center post. If one is not careful, it is easy to pull the wire when tightening the top nuts. This may tighten the coil at the top of the wick, ands can easily lead to the wire cutting through any oxidation layer. Doing so may result in a short, and consequently, a hot spot. We did experience this with our 32-gauge setup, though it was not an issue with the thicker 28-gauge wire.
Other issues that have been mentioned include rough edges on the glass tanks. While these seemed to be quite common in early batches of the AGA-T2, they seem to be less common now. It seems likely that the manufacturer has responded to complaints about tank quality.
Another common complaint we’ve heard is that the tank fits loosely, causing leaks. In most cases, though, this has been caused by a misunderstanding of how to assemble the tank. When the tank is put in place, the AGA-T2 can be tightened down by simply twisting the top cap; it will then screw down tightly onto the tank. In most cases where leaks were reported, they were the result of having tried to use the nuts on the center post to tighten things down, and yes, if you only do this the AGA-T2 will leak. Don’t ask us how we know this; it’s a little embarrassing.

The Drunker by SmokTech

  
SmokTech’s new Drunker is an odd little rebuildable atomizer. Shaped like a beer bottle, it holds two wicks that pass into a 5ml tank through four wick holes. At the top of the unit, the wicks meet in a tiny ceramic cup where a rebuildable coil vaporizes the juice.
We didn’t expect much from it, frankly. The dangling strings and knurled design give it a bit of a retro look (retro being relative to vaping timelines, of course, and meaning that the Drunker looks like an atomizer from the long-ago days of, say, 2011 or early 2012). However, we’ve found the wick and coil design, even right out of the box with no fiddling, to be very effective. The included coil is approximately 2.4 ohms (ours measured 2.6 ohms). Vapor production has been very good, flavor is minimally muted, and we have experienced no leaks or dry hits, even under heavy use.
Rebuilding the Drunker is a relatively simple affair, the only really difficult parts being convincing the ends of the wicks to go through the small-diameter holes into the tank, and feeding the wires through the tiny holes in the cup. Adeline submitted an excellent post on ECF, “Inside the Drunker Tank,” illustrating how to rebuild the atomizer. We used this as our guide and found it to be relatively painless.
The Drunker’s diameter is approximately 20mm, making it ideal for slant-top mods. If you happen to have a Kamry KTS x6 like the one we recently reviewed, the Drunker is a particularly excellent aesthetic choice, as the fit is flush and the knurling of the Drunker matches the knurling on the KTS quite well. As one of our squad members pointed out, the two look like they were made for each other.
While it is quite possible to use the Drunker without a drip tip due to the long neck, standard 510 tips will fit, and may be more comfortable to use.